Godex EZPi-1300 User Manual

User’s Manual EZPi-1000 Series P/N. 920-013011-01 Rev. A, 08.2009

1-4. Printer Parts 1. Cover Open Button 2. Top Cover 3. Label Roll Core 4. Ribbon Rewind Wheel 5. LCD Module Case 6. Printing Mechanism 7. Fron

1. Ribbon Supply Shaft 2. Label Guide 3. Platen Roller 4. Print Line Adjustment Gear 5. Label Sensor 1. LCD Control Panel 2. Fan-Fold Label

2. Printer Installation This printer model has the following print modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer t

4. Feed the ribbon from the Ribbon Supply Shaft under the Print Head. 5. Wrap the ribbon around the Ribbon Shaft and stick the ribbon onto the Empt

2-2. Label Installation 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Insert the Label Roll Core into the label roll.

2-3. Label Roll Core Installation Instruction (A) 1” roll core installation (B) 1.5” roll core installation (C) 3” roll core installation EZPi-1

2-4. Card / Hang tags Installation When installing cord tags, the tag hole must align with the sensor arrow (as indicated in figure), then use the Lab

2-6. Driver Installation 1. Insert product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of d

6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displaye

3. Control Panel 3-1. Control Panel Introduction Control keys FEED PAUSE CANCEL LED indicators Power (Ready) The Power (Ready) light is to indicat

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant

With different combinations of FEED PAUSE and CANCEL keys, the printer can perform various functions as follows: Item Key Beep LCD Message Descript

3-3. Setting mode In the Setting Mode, changes can be made according to requirement on the printing mode, options, media type, and parallel interface

Below are general descriptions of setting items. Darkness Default: 15Set the darkness of printing result. The setting value is from 0 to 19 and the de

Code Page Default: Code Page 850 Code Page850 Code Page852 Code Page437 Code Page860 Code Page863 Code Page865 Code Page857 Code Page861 Code Page862

The diagram of Setting Mode  To enter the Setting mode, please press and hold the Pause key about 3 to 4 seconds until the buzzer beeps 3 tim

3-4. Self-Test The Self-Test function will help user to check whether the printer is operating normally. The printer will go back to standby mode afte

3-5. Dump Mode When the print result doesn’t match the label setting, it’s recommended to go into the Dump Mode to check whether there is a mistake in

3-7. Keyboard Mode EZPi-1000 series printer can support keyboard with PS2 interface. To connect the PS2 keyboard, please do as follows: 1. Please be

6. LCD will show the Serial Number Prompt. 7. Key in the start value. (Example:00001)8. LCD will show the first Variable Prompt.9. Key in the var

14. The printer will print out 3 labels that include user-defined variables and serial number. EZPi-1000 User’s Manual 28

Safety Instructions Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben. 1. Die Geräte nicht der Feuchtigkeit aussetzen. 2. Be

3-8. Error Messages If problems occur that prevent the printer printing normally, the printer will beep as warning, and error messages will be display

Memory Full 2 beeps twice Memory is full Delete unnecessary data in the memory or use CF Card. Filename can not be found 2 beeps twice Can’t fi

4. Accessory 4-1. Stripper Installation 1 Stripper Module 2 Screw (TAP 3*8) x 2pcs 【Note1】 Please power off the printer before installing the stripp

5. Plug in the stripper connector onto the switchboard socket. (refer to right figure) 【Note】 There are 2 sockets on the converting boards (one is

10. Follow the direction as shown in figure to feed the liner across the stripper. 11. Close the upper print mechanism and the stripper. 12. Pre

4-2. Cutter Installation 1 Cutter Module 2 Screw (TAP 3*8) x 2pcs 21 【Note1】 Please power off the printer before installing the cutter module. 【Note2

6. Place the left side of the stripper first, and then fit the right side. 7. Flip the cutter module downward to open the cutter. 8. Hold the cut

4-3. WLAN Module Installation 1 Ethernet Cable 1.8M 2 Secure Screw*1 3 Bracket Screw*2 4 Module Bracket 5 WLAN module 6 Module Connection Wire

6. Unscrew the Ethernet Module Secure Screw. 7. Remove the Ethernet Module and its connection wire. 8. Unscrew the screw of PS2 Port with long-no

13. Align the WLAN module to the Ethernet port and plug into it. 14. Secure the module onto the back plate. 15. Thread the Module Connection Wire

Safety Instructions Please read the following instructions seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipme

17. Put the Fixture Plate first then the Washer and tighten the Nut to mount Antenna Connection Wire on the printer. 【Note】 It is suggested to tight

4-4. CF Card Adapter Installation 1 CF Card Adapter (Front) 2 CF Card Adapter (Back) 【Note】 Please power off the printer before installing the CF

4-5. CF Card Instruction EZPi-1000 series printers can read the CF Card after installed the CF Card Adapter. If the built-in memory is insufficient

5. Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts may be caused by dusty print head, ribbon stain or label liner glue.

5-3. Print Line Adjustment To get better printing balance and quality, use print head adjusting gear to adjust the contacting surface between print he

5-5. Troubleshooting Problem Recommended Solution Power on the printer, but the LED does not light up ♦ Check the power connector is plugged correct

1. BARCODE PRINTER... 5 1-1. Printer Accessories...

1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and store appropriately.  Barc

Code Pages CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737 WINDOWS 1250, 1251, 1252, 1253, 1254, 1255 Unicode (UTF8, UT

1-3. Communication Interface Parallel Interface Handshake : DSTB connects to the printer, BUSY connects to the host Interface cable : Parallel cab

Internal Interface UART1 wafer Ethernet module N.C 1 1N.C TXD 2 2RXD RXD 3