Godex EZ-2300Plus User Manual

P/N. 920-011911-05 Rev. C, 02.2011 User Manual EZ2000 Plus/ EZ6000 Plus

EZ2000 Plus / EZ6000 Plus User Manual 9 USB port Connector type : Type B Pin No. 1 2 3 4 Function VBUS D- D+ GND PS/2 port Pin No. 1

EZ2000 Plus / EZ6000 Plus User Manual 10 Applicator wafer Applicator module +5V 1 1 +5V +24V 2 2

EZ2000 Plus / EZ6000 Plus User Manual 11 1-4. Getting to know your printer External view 4312 1. Operator panel with LCD display 2. Lower cove

EZ2000 Plus / EZ6000 Plus User Manual 12 Internal view 123456712111098 1. Ribbon rewind hub 2. Ribbon supply hub 3. Print mechanism 4.

EZ2000 Plus / EZ6000 Plus User Manual 13 2. Printer setup This printer supports the following printing methods: Thermal transfer printing (TTP) Req

EZ2000 Plus / EZ6000 Plus User Manual 14 5. Place the label roll on the label supply hub, pushing it right up to the printer housing. (Do not appl

EZ2000 Plus / EZ6000 Plus User Manual 15 9. The labels pass between the wall of the printer housing and the adjustable paper guide. 【Note】 Pass t

EZ2000 Plus / EZ6000 Plus User Manual 16 2-2. Loading the ribbon 1. Place the printer on a flat surface and open the printer cover. 2. Pull out

EZ2000 Plus / EZ6000 Plus User Manual 17 2-3. Connecting the printer to the host computer 1. Please make sure that the printer is switched off.

EZ2000 Plus / EZ6000 Plus User Manual 18 2-4. Installing the driver 1. Insert the product CD in the CD/DVD drive of the host computer and open the

EZ2000 Plus / EZ6000 Plus User Manual 1 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the li

EZ2000 Plus / EZ6000 Plus User Manual 19 6. Specify the port used to connect the printer to the host computer. 7. Enter a printer name and ass

EZ2000 Plus / EZ6000 Plus User Manual 20 3. Operator panel 3-1. Operator panel – introduction Function buttons FEED PAUSE CANCEL LED indicators

EZ2000 Plus / EZ6000 Plus User Manual 21 You can combine the FEED, PAUSE and CANCEL buttons in a number of ways to perform different printer functi

EZ2000 Plus / EZ6000 Plus User Manual 22 3-3. Settings mode In settings mode, you can change different settings, such as the printing mode, accesso

EZ2000 Plus / EZ6000 Plus User Manual 23 The following table lists descriptions of the available settings and options: Darkness Speed Default: 10 S

EZ2000 Plus / EZ6000 Plus User Manual 24 LCD language Default:Code pages installed English English Simplified Chinese Traditional Chinese Spanish

EZ2000 Plus / EZ6000 Plus User Manual 25 USB / Ethernet Default: USBPreview USB: Enables the USB port. Ethernet: Enables the Ethernet port. Le

EZ2000 Plus / EZ6000 Plus User Manual 26 Settings mode diagram Items marked "*" are the default settings.

EZ2000 Plus / EZ6000 Plus User Manual 27 3-4. Self test The self-test function lets you check whether the printer is functioning normally. Here

EZ2000 Plus / EZ6000 Plus User Manual 28 3-5. Dump mode If the label settings do not match the printer output, you should switch the printer to du

EZ2000 Plus / EZ6000 Plus User Manual 2 Safety instructions Please read the following instructions carefully. 1. Keep the equipment away from hu

EZ2000 Plus / EZ6000 Plus User Manual 29 3-7. Keyboard mode The printers of the EZ2000 Plus and EZ6000 Plus series support keyboards with a PS/2 i

EZ2000 Plus / EZ6000 Plus User Manual 30 6. The input form for the serial number is now shown on the display. 7. Specify a start value (example

EZ2000 Plus / EZ6000 Plus User Manual 31 14. The printer will print three labels with the values for the two variables and the serial number spec

EZ2000 Plus / EZ6000 Plus User Manual 32 3-8. Error alerts In the event of a problem that prevents normal functioning of the printer, you will see

EZ2000 Plus / EZ6000 Plus User Manual 33 Memory full 2x2 beeps The memory is full. Delete data you no longer need from the memory or use a CF

EZ2000 Plus / EZ6000 Plus User Manual 34 4. Accessories 4-1. Internal rewinder (EZ2000 Plus) 1 Rewinder 1234 2 Retention clip 3 Screws (set of 4) 4

EZ2000 Plus / EZ6000 Plus User Manual 35 3. Remove the retention clip from the rewinder. 4. Secure the rewinder on the printer housing using the

EZ2000 Plus / EZ6000 Plus User Manual 36 4-2. Installing the rewinder guide (EZ2000 Plus) 1. Unscrew the screw marked in the illustration on the f

EZ2000 Plus / EZ6000 Plus User Manual 37 4-3. Label dispenser (EZ2000 Plus) 1. Unscrew the screw marked in the illustration on the front of the pr

EZ2000 Plus / EZ6000 Plus User Manual 38 8. Wind the label liner around the rewinder and secure it using the retention clip. 9. Return the print

EZ2000 Plus / EZ6000 Plus User Manual 3 1. BARCODE PRINTER ... 41-1. Box content

EZ2000 Plus / EZ6000 Plus User Manual 39 4-4. Internal rewinder for EZ6000 Plus 1 Motor 12345678 2 Rewinder 3 Rewinder connector bracket 4 Retent

EZ2000 Plus / EZ6000 Plus User Manual 40 7. Remove the two screws securing the connector bracket from the inside of the printer housing. 8. Now

EZ2000 Plus / EZ6000 Plus User Manual 41 14. Install the motor in the back section of the printer housing and align it with the 4 screw holes. 15

EZ2000 Plus / EZ6000 Plus User Manual 42 19. Connect the cable with the 5-pin connector to the jack marked "CUTTER" on the motherboard.

EZ2000 Plus / EZ6000 Plus User Manual 43 27. Now load the label stock. 28. Pass the label stock through the rewinder from the bottom up. Secure

EZ2000 Plus / EZ6000 Plus User Manual 44 4-5. Installing the label dispenser (EZ6000 Plus with rewinder) 1 Dispenser module 2 Cable clips (set of

EZ2000 Plus / EZ6000 Plus User Manual 45 5. Connect the dispenser cable connector to the rewinder jack. 6. Route the connection cable along the

EZ2000 Plus / EZ6000 Plus User Manual 46 11. Wind the label liner around the rewinder and secure it using the retention clip. 12. Return the pri

EZ2000 Plus / EZ6000 Plus User Manual 47 4-6. Installing the cutter 1 Cutter cover (EZ2000 Plus) 12345 2 Cutter cover (EZ6000 Plus) 3 Cutter module

EZ2000 Plus / EZ6000 Plus User Manual 48 3. Secure the cutter module on the printer housing using the screws. 4. Connect the cutter cable conne

EZ2000 Plus / EZ6000 Plus User Manual 4 1. Barcode printer 1-1. Box content Please check that all of the following items are included with your pr

EZ2000 Plus / EZ6000 Plus User Manual 49 4-7. Installing the parallel / PS/2 adapter 1 Parallel cable 123 4 2 Parallel / PS/2 adapter 3 Connection

EZ2000 Plus / EZ6000 Plus User Manual 50 4. Install the parallel/PS/2 adapter in its place and secure it on the housing with screws. 5. Connect

EZ2000 Plus / EZ6000 Plus User Manual 51 4-8. Installing the applicator interface 1 Applicator interface 12 2 Screws (set of 2) 1. Place the prin

EZ2000 Plus / EZ6000 Plus User Manual 52 4. Pass the applicator cable through the opening into the housing. 5. Connect the applicator cable to t

EZ2000 Plus / EZ6000 Plus User Manual 53 4-9. Installing the WLAN module – EZ2000 Plus / EZ6000 Plus 1 Ethernet cable, 1.8 m 2 Fastening screws (s

EZ2000 Plus / EZ6000 Plus User Manual 54 6. Plug the other end of the connection cable into the motherboard socket. 7. Secure the module bracket

EZ2000 Plus / EZ6000 Plus User Manual 55 10. Put the washer on the antenna connector and secure the connector on the antenna bracket using the nut

EZ2000 Plus / EZ6000 Plus User Manual 56 5. Maintenance and adjustment 5-1. Installing / removing the print head module 1. Open the printer cover.

EZ2000 Plus / EZ6000 Plus User Manual 57 5-2. Adjusting the print line Please contact your local dealer for technical support. 1. Open the prin

EZ2000 Plus / EZ6000 Plus User Manual 58 5-3. Adjusting the ribbon tension You can adjust the ribbon tension by turning the ribbon shaft knob (gree

EZ2000 Plus / EZ6000 Plus User Manual 5 Printer Language EZPL, GEPL (Godex Eltron® Printer Language), GZPL (Godex Zebra® Printer Language) Softwar

EZ2000 Plus / EZ6000 Plus User Manual 59 5-4. Cleaning the thermal print head Dirt on the print head or ribbon may result in inadequate print quali

EZ2000 Plus / EZ6000 Plus User Manual 60 5-5. Adjusting the balance and print head tension 1. Open the printer side cover. 2. Pull out the pr

EZ2000 Plus / EZ6000 Plus User Manual 61 5-6. Ribbon shield settings 1. The use of different ribbon materials may cause wrinkling of the ribbon,

EZ2000 Plus / EZ6000 Plus User Manual 62 5-7. Cutter settings 1. Socket head screws for adjusting the cutter are located on both sides of the cutt

EZ2000 Plus / EZ6000 Plus User Manual 63 5-8. Troubleshooting Problem Solution The printer is switched on but the display does not light up. ♦ Ch

EZ2000 Plus / EZ6000 Plus User Manual 6 EZ6000 Plus series Model EZ6200 Plus Print Method EZ6300 Plus Thermal Transfer / Direct Thermal Resolutio

EZ2000 Plus / EZ6000 Plus User Manual 7 Barcodes 1-D Bar codes: Code 39, Code 93, Code 128 (subset A, B, C), UCC/EAN-128 K-Mart, UCC/EAN-128, UPC

EZ2000 Plus / EZ6000 Plus User Manual 8 1-3. Interfaces Parallel port Handshaking : DSTB is sent to the printer, BUSY to the host computer Interfa