Godex EZ2050 series User Manual

1EZ2050/EZ2150 BARCODE PRINTERUSER MANUALUser ManualVersionIssue DateP/N : EZ2050 series : Rev. D : 2013.07.18 : 920-014411-00

62 Printer Setup 9. The labels pass between the wall of the printer housing and the adjustable paper guide. 【Note】 Pass the labels through the pr

72 Printer Setup2.2 Loading the Ribbon1. Place the printer on a flat surface and open the printer cover. 2. Pull out the print head release l

82 Printer Setup2.3 Connecting the Printer to the Host Computer1. Please make sure that the printer is switched off.2. Connect the power c

91. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD. Select the ico

102 Printer Setup2 Printer Setup4. Specify the port used to connect the printer to the host computer.6. Once the installation is complete,

112 Printer Setup7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder.Godex E

123 Printer Setting and Control3.1 Operation PanelOperation Panel Introduction Function buttons FEED PAUSE CANCEL LED indicators POWER The PO

133 Setting and Control for Operation Panel3.2 Function buttons – introduction FEED button When you press the FEED button, the printer moves th

143 Setting and Control for Operation Panel3.2 Settings modeIn settings mode, you can change different settings, such as the printing mode or me

153 Setting and Control for Operation Panel Direct Thermal / Thermal Transfer DT mode TT mode When reaching this item, press button to set t

ContentsEZ2050/EZ2150 USER MANUALCONTENTSContents1. BARCODE PRINTER ... 1 1-1. Box

163 Setting and Control for Operation Panel3.4 Label Calibration and Self TestLabel CalibrationThe printer can automatically detect and store la

173 Setting and Control for Operation PanelLabel Calibration ButtonA hardware button to make a Label Calibration while printer encountering ‘’Media

183 Setting and Control for Operation Panel3.5 Dump modeIf the label settings do not match the printer output, you can switch the printer to dum

193.6 Error alerts3 Setting and Control for Operation PanelIn the event of a problem that prevents normal functioning of the printer, you will s

204 Accessories4.1 Internal rewinder1 Rewinder 1234 2 Retention clip 3 Screws (set of 4) 4 Rewinder guide 【Note】 Maximum height of the rewound m

213. Remove the retention clip from the rewinder. 4. Secure the rewinder on the printer housing using the four screws supplied. 12 5. Now connect

224.2 Installing the rewinder guide4 Accessories1. Unscrew the screw marked in the illustration on the front of the printer, which secures the

234.3 Label dispenser4 Accessories3. Wind the label liner around the rewinder and secure it using the retention clip. 4. Return the print hea

244 Accessories8. Wind the label liner around the rewinder and secure it using the retention clip. 9. Return the print head release lever to its

254.4 Installing the cutter4 Accessories1 Cutter cover 2 Cutter module 3 Cable clips 4 Screws (set of 4) 【Note 1】 Remember to switch off the pr

DeclerationEZ2050/EZ2150 USER MANUALFCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a

264 Accessories3. Secure the cutter module on the printer housing using the screws. 4. Connect the cutter cable connector to the cutter jack on

274.5 Installing the Parallel adapter4 Accessories1 Parallel cable 123 4 2 Parallel adapter 3 Connection cable 4 Screws (set of 2) 1. Check wh

284. Install the Parallel adapter in its place and secure it on the housing with screws. 5. Connect the 30-pin connection cable to the motherboard

294 Accessories4.6 Installing the Applicator interface1 Applicator interface 12 2 Screws (set of 2) 1. Place the printer on a flat surface and

304 Accessories4. Pass the applicator cable through the opening into the housing. 5. Connect the applicator cable to the jack marked "APP&qu

315 Maintenance and Adjustment5.1 Installing / removing the print head module1. Open the printer cover. 【Note】 Remember to switch off the prin

325.2 Adjusting the print line5 Maintenance and AdjustmentPlease contact your local dealer for technical support. 1. Open the printer cover.

335.3 Adjusting the print lineYou can adjust the ribbon tension by turning the ribbon shaft knob (green wheel at the base of the ribbon supply hub

345 Maintenance and Adjustment5.4 Cleaning the thermal print headDirt on the print head or ribbon may result in inadequate print quality (no pri

355 Maintenance and Adjustment5.5 Adjusting the balance and print head tension1. Open the printer side cover. 2. Pull out the print head relea

Safety instructionsEZ2050/EZ2150 USER MANUALSAFETY INSTRUCTIONSPlease read the following instructions carefully.1. Keep the equipment away from hum

365 Maintenance and Adjustment5.6 Ribbon shield settings1. The use of different ribbon materials may cause wrinkling of the ribbon, which in tu

375 Maintenance and Adjustment5.7 Cutter settings1. Socket head screws for adjusting the cutter are located on both sides of the cutter. 2. I

385 Maintenance and Adjustment5.8 Troubleshooting**** If any problems occur that are not described here, please contact your dealer.Problem S

AppendixEZ2050/EZ2150 USER MANUALAPPENDIXPRODUCT SPECIFICATIONS****Specifications are subject to change without notice. All company and/or product nam

AppendixAppendixINTERFACESerial PortDefault settings： Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFFprotocol and RTS/CTS RS232 Housing(

AppendixINTERFACEEZ2050/EZ2150 USER MANUALAPPENDIXConnector Type : Type B USBPin NO. 1 2 3 4 Function VBUS D- D+ GND Internal interfaceUART1 waf

AppendixAppendixEZ2050/EZ2150 USER MANUALAPPENDIXApplicator wafer Applicator module +5V 1 1 +5V +24V

11 Barcode PrinterPOWERRIBBONDENSITYMEDIASPEEDFEEDCANCELPAUSE1.1 Box ContentPlease check that all of the following items are included with your

21 Barcode Printer1.2 Getting to Know Your PrinterExternal view 1. Operator panel 2. Lower cover plate 3. Viewing window 4. Printer cov

31 Barcode Printer123456712111098 1. Ribbon rewind hub 2. Ribbon supply hub 3. Print mechanism 4. Platen roller 5. Tear-off plate 6.

42 Printer SetupThis printer supports the following printing methods:Thermal transfer printing (TTP)：Requires a ribbon for transferring a printed i

52 Printer Setup 5. Place the label roll on the label supply hub, pushing it right up to the printer housing. (Do not apply too much pressure to a