Godex EZ2350i User Manual Page 1

1EZ2250i/EZ2350i BARCODE PRINTERUSER MANUALUser ManualVersionIssue DateP/N : EZ2250i series : Rev. E : 2013.11.28 : 920-014611-00

62 Printer Setup9. The labels pass between the wall of the printer housing and the adjustable paper guide. 【Note】 Pass the labels through the pri

72 Printer Setup2.2 Loading the Ribbon1. Place the printer on a flat surface and open the printer cover. 2. Pull out the print head release l

82 Printer Setup2.3 Connecting the Printer to the Host Computer1. Please make sure that the printer is switched off.2. Connect the power c

92 Printer Setup* If the Super Wizard program did not run automatically, you can either turn on the “Auto-run” setting for your CD/DVD driver

102 Printer Setup4. As the printer driver and GoLabel are installing, a screen will display a progress bar.5. Once the installation is comple

111. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD. Select the ic

122 Printer Setup2 Printer Setup4. Specify the port used to connect the printer to the host computer.6. Once the installation is complete,

132 Printer Setup7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder.Godex E

143 Printer Setting and Control3.1 Operation PanelOperation Panel IntroductionFEED ButtonWhen you press the FEED button, the printer moves the l

153 Setting and Control for Operation Panel3.2 LCD Interface IntroductionGetting StartedPress the POWER button to turn on the printer, and the S

ContentsEZ2250i/EZ2350i USER MANUALCONTENTSContents1. BOX CONTENT ... 1 1.1

163 Setting and Control for Operation PanelOperations on Setting PageOn MAIN PAGE, press  or  button to move the cursor and select the functions.

173 Setting and Control for Operation PanelPress FEED button will apply the setting value you just selected, and the red tick will appear to mark t

18On SETTING PAGES, press  button will go back to the MAIN PAGE screen.Exit from Current Page to Ready StatusThe icon on top-left corner displays the

19On MAIN PAGE, select the “EXIT” icon and press the FEED button to exit from SETTING MODE and the printer goes back to READY status.orEXIT from Setti

203.3 LAN SettingOperations on Setting PageOn MAIN PAGE，press  or  button to move the cursor and select the functions.Select a designated functio

213 Setting and Control for Operation PanelThe default of DHCP is Disable. ，Press  or  button to change the setting values.Press FEED button twic

223 Setting and Control for Operation Panel3.4 LCD PasswordOperations on Setting PageOn MAIN PAGE, press  or  button to move the cursor and se

233 Setting and Control for Operation PanelSelect  button again to setup the password Press FEED button onece to exit.Press FEED button twice to s

243 Setting and Control for Operation Panel3.5 LCD Interface FunctionMain PagePrinter SettingLabel SettingDeviceAnalysisExitSetting items for pr

253 Setting and Control for Operation PanelSetting Items in Setting ModePrinter SettingLabel SettingLCD Language English German 繁體中文 简体中文 Wizard Sp

EZ2250i/EZ2350i USER MANUALFCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a CLASS A

26DeviceAnalysisExitBuzzer Apply Cancel Optional Setting Option None Cutter Label Dispensor Applicator Pre-Printing Apply Cancel Serial Port Setting B

27Status of LCD InterfaceWhen printer is on standby status (ready to print), the LCD interface will display “Ready” on screen.You can only print on th

283 Setting and Control for Operation Panel3.6 Label Calibration and Self TestLabel CalibrationThe printer can automatically detect and store la

293 Setting and Control for Operation PanelLabel Calibration ButtonA hardware button to make a Label Calibration while printer encountering ‘’Media

303 Setting and Control for Operation Panel3.7 Dump modeIf the label settings do not match the printer output, you can switch the printer to dum

313 Setting and Control for Operation Panel3.8 Error AlertsIn the event of a problem that prevents normal functioning of the printer, you will s

323 Setting and Control for Operation PanelOperation Panel Status Type Beeps Description Solution File Error 2 x 2 beeps The memory is full. The

333 Setting and Control for Operation Panel3.9 USB HostDefinition : USB Host port supports either device：USB memory stick, keyboard or scanner.P

343 Setting and Control for Operation Panel** The USB Host port on ‘’i’’ ‘’x’’ model printer is without ‘’HUB’’ function.** The USB Memory Stic

354 NetSetting for Ethernet4.1 Installing the NetSetting softwareThe NetSetting software is used to manage the network configurations when conne

EZ2250i/EZ2350i USER MANUALSAFETY INSTRUCTIONSPlease read the following instructions carefully.1. Keep the equipment away from humidity.2. Befor

364 NetSetting for Ethernet4.2 The Interface of NetSettingClick the NetSetting icon to start the program; you will see the start page as below.

37**** To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please contact your network admi

38You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Alert Path SettingNetSetting will send the alert m

39You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Alert Message SettingFor the alert message notific

40You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Printer ConfigurationSet or change the configurati

41You can press “Send Command” button to send printer commands via Ethernet port and control the printer remotely.User CommandThe “User Command” tab p

42In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer configurations back to factory default

435 Accessories5.1 Internal rewinder1 Rewinder 1234 2 Retention clip 3 Screws (set of 4) 4 Rewinder guide 【Note】 Maximum height of the rewound m

445 Accessories3. Remove the retention clip from the rewinder. 4. Secure the rewinder on the printer housing using the four screws supplied. 12

455 Accessories5.2 Installing the rewinder guide1. Unscrew the screw marked in the illustration on the front of the printer, which secures the

11 Barcode Printer1.1 Box ContentPlease check that all of the following items are included with your printer.EZ2250i/EZ2350i Barcode PrinterUSB

465 Accessories5.3 Label dispenser1. Unscrew the screw marked in the illustration on the front of the printer, which secures the lower cover pl

475 Accessories8. Wind the label liner around the rewinder and secure it using the retention clip. 9. Return the print head release lever to its

485 Accessories5.4 Installing the cutter1 Cutter cover 2 Cutter module 3 Cable clips 4 Screws (set of 4) 【Note 1】 Remember to switch off the pr

495 Accessories3. Secure the cutter module on the printer housing using the screws. 4. Connect the cutter cable connector to the cutter jack on

505 Accessories5.5 Installing the Parallel adapter1 Parallel cable 123 4 2 Parallel adapter 3 Connection cable 4 Screws (set of 2) 1. Check wh

515 Accessories4. Install the Parallel adapter in its place and secure it on the housing with screws. 5. Connect the 30-pin connection cable to t

526 Maintenance and Adjustment6.1 Installing / removing the print head module1. Open the printer cover. 【Note】 Remember to switch off the print

536 Maintenance and Adjustment6.2 Adjusting the print linePlease contact your local dealer for technical support. 1. Open the printer cover.

546 Maintenance and Adjustment6.3 Adjusting the print lineYou can adjust the ribbon tension by turning the ribbon shaft knob (green wheel at the

556 Maintenance and Adjustment6.4 Cleaning the thermal print headDirt on the print head or ribbon may result in inadequate print quality (no pri

21 Barcode Printer1.2 Getting to Know Your PrinterExternal view 1. Operator panel 2. Lower cover plate 3. Viewing window 4. Printer cov

566 Maintenance and Adjustment6.5 Adjusting the balance and print head tension1. Open the printer side cover. 2. Pull out the print head relea

576 Maintenance and Adjustment6.6 Ribbon shield settings1. The use of different ribbon materials may cause wrinkling of the ribbon, which in tu

586 Maintenance and Adjustment6.7 Cutter settings1. Socket head screws for adjusting the cutter are located on both sides of the cutter. 2. I

Appendix6 Maintenance and Adjustment6.8 Troubleshooting**** If any problems occur that are not described here, please contact your dealer.Proble

AppendixEZ2250i/EZ2350i USER MANUALAPPENDIXPRODUCT SPECIFICATIONS****Specifications are subject to change without notice. All company and/or product n

AppendixAppendixINTERFACESerial PortDefault settings： Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFFprotocol and RTS/CTS RS232 Housing(

AppendixINTERFACEEZ2250i/EZ2350i USER MANUALAPPENDIXConnector Type : Type B USBPin NO. 1 2 3 4 Function VBUS D- D+ GND Internal interfaceUART1 w

AppendixFILE MANIPULATION WHEN USING USB STICKEZ2250i/EZ2350i USER MANUALAPPENDIXFile Manipulation The files in both devices (USB memory stick and

31 Barcode PrinterInternal view 1. Ribbon rewind hub 2. Ribbon supply hub 3. Print mechanism 4. Platen roller 5. Tear-off plate 6.

42 Printer SetupThis printer supports the following printing methods:Thermal transfer printing (TTP)：Requires a ribbon for transferring a printed i

52 Printer Setup5. Place the label roll on the label supply hub, pushing it right up to the printer housing. (Do not apply too much pressure to av